Heatvape Kayfun 3.1 and Mini V2.1 from 3Avape

The Heatvape Kayfun 3.1 and Mini V2.1 were sent to me from 3Avape:

Heatvape Kayfun 3.1 - $17.50 : 3Avape, Wholesale & Retail

Heatvape Kayfun Mini V2.1 - $21.50 : 3Avape, Wholesale & Retail

One of the first things is how nice the boxes are from Heatvape




First up the:
Heatvape Kayfun 3.1
Features: Dual coil or single coil
-Constructed from solid stainless steel
-Rebuildable Tank Atomizer
-Juice Capacity 4.5ml
-Adjustable Airflow
-Reduced Atomizing Chamber
-Simple to Rebuild -Integrated Drip tip and 510 Drip tip Adaptor
-Overflow Collection Cup -
Available Finish Options Polished Stainless Steel(Delta) Brushed and Matte(Beta)
-Includes 510 Drip Tip Adaptor , Spare Post Screws , Spare O-Rings
-Diameter 22mm
It comes with 1x Kayfun 3.1 atomizer 1x replacement plastic tube 1x pack of wick 1x pack of rubber seal rings, post screws and a steel ring 1x screwdriver 1x 10ml semi-transparent empty bottle with needle tip

Very well made bit of kit, comes with lots of extra stuff.
Has a bigish HeatVape logo on the side though, not a huge fan of that



Striped it down, all comes apart nicely, but the center plastic tube isn't great with its threads, possible problems there I think if you're unscrewing it a lot.



It's a side fill with an adjustable airflow.
I don't use the side fill as i just top fill

Got it sat on my rDNA 30 and a mech mod




Overall a typical KayFun vape.
Well made apart from the plastic center tube which i mentioned.
It comes in a few colors as in on 3Avpe.

A big thanks to 3avpae.com for sending me this
I will be putting it up in a GiveAway very soon for a member to get the chance to win it.
V

 

The Heatvape Kayfun Mini V2.1;

Heatvape Kayfun Mini V2.1 - $21.50 : 3Avape, Wholesale & Retail

Basic Information:
Depth: 14MM
Height: 87.6MM
Width: 14MM
Capacity:3.0ml

Features:
1, Airflow control and airhole on side
2, Clear window section
3, Universal drip tip connection

It comes with

1x Kayfun Mini V2.1 Rebuildable Atomizer (replica)

1x plastic tube

1x screwdriver

1x decorative ring

1x 10ml empty plastic dropper bottle

1x long cap of the evaporation chamber

3x spare post screw

6x spare O-ring

7x heating wire /wick(5 pcs short and 2 pcs long)

Again, a great presentation box and a lot of extra stuff with it




This is just the same as the KayFun 3.1 but in a smaller version
It is very well made and has all the tubes for different sizes.
I like to see my juice so I like to use the clear plastic tube on the bottom as per the picture

Stripped it down:


Easy to build really, just the same as any KayFun
The fill hole on the side again with adjustable airflow there too
I tend to fill from the top, but there's not a lot of room so a little difficult but ok.
Also I found thicker VG juices too much for this, a 50/50 pg/vg is fine, or even then higher PG.

Top filling always keep your finger over the air hole, screw the top back up, flip upside down, keeping your finger over the air hole , tighten up the top can while upside, flip back over and take off your finger..

On my DNA 30 and mech mod



Overall very nice but just too small for me.

Thanks for 3avape.com for sedning me this
As always I will be Giving it away very soon for a member to have the chance to win it
V

 

Any questions about either of the above just ask me
V

 

As in from one of my other KayFuns?
Good idea, I will try that....