What is suitable ohms for 130 or higher wattage

Hello guys, I just bought new rda atomizer which is avocado 24 mm.

I was wondering how to make coils suitable for 130 or higher watt. (Because I want a lot of vaper )

Anyway, I saw one website that selling pre built juggernaut coil 0.2 ohm.

Will it be suitable to run 130 or more watt if I build dual juggernaut 0.2 ohm coils on my avocado rda?

Anyone have any recommned for running 130 watt?

 

I slightly don't get it by what you saying about don't do it. Sorry. Btw, I am using Joyetech cuboid upgraded to 200 watt and using dual AWT 40A batteries. What can be suitable for running 140 watt?

 

Thanks for help mate. Really appreciate it

 

Dual 0.2 ohm coils will put you right at the limit of the Cuboid. It will not fire below 0.1 ohms. If the coils are off just by a little and you end up at .09 or lower the mod will not fire. There are also a couple of things to take into consideration when building for the Cuboid. The device has a 9 volt maximum output and has a 25 amp cut off safety limit. If you put a 0.1 ohm build in it, the most wattage you could get would be 62 watts because you will hit the 25 amp limit. A 0.2 ohm build will give you a maximum of 125 watts before hitting the 25 amp cut off. 0.3 ohms will give you 187 watts before hitting the cut off. The magic number for hitting the max on this mod would be a .32 ohm build. 8 volts, 25 amps, and 200 watts. I've got a feeling the the Avocado is going to be spewing hell fire at 140 watts, but you may like it.

 

I did a 200w build for rx200/velocity, post is here - How to build 200w coils? | Thailand Vapers

 

still don't know why many people think they need Sub Ohm Builds below .3 or .2 Ohm to Vape high Wattage ..

If you use thicker wire you can Vape 200 Watts on Coils with .5 Ohms or higher .. My Limitless is running a dual Clapton 26 Gauge Coil with .8 Ohm and if i want i can Bump it up to 150 easy without drain my Batteries like crazy

By the way your AWT Batteries never have 40 AMP don't go over 20 thats what they can Handle

Test of AWT IMR18650 3000mAh (Red) 40A 2015

 

Misunderstanding ohms law, and the capability of the equipment, would be my guess ...

 

With the current vaping regulations climate here, please don't blow massive 130W vapor clouds or accidentally explode your AWT "40" Amp-powered mod in public. You really should have higher amp capable (real) batteries for what you say you are looking to do.

Also, at those values and your goal of clouds, you should probably also be using something like an RDA as opposed to a tank atty though some could allow it the Avocado really isn't designed for it.

 

We had a threat here that which was slightly tongue in the cheek talking about girls blowing big clouds and I remain, from obvious reasons don't do it, or at least don't do it in public.
If you feel you need to try it like Skuba, then read his thread first.

As for me I think anything above 40 - 50 W is waste.

 

You're using the ceramic block and single coil at the Griffin?

Sent from my T03 using Tapatalk

 

0.45 Ohm dual coil on my Crius, rocking at 35W with great flavor and plenty of vapor.

Basically I would not recommend building very low (0.1 to 0.30 in any tank as they tend to give a vapor way too hot. If you want to experience very big clouds with very low ohms your best bet is to go for a dripper.